Home > Stocks, Grips, and Handguards > Vertical Grips, Hand Stops >

BCMGUNFIGHTER KAG - KeyMod™ - Black

BCMGUNFIGHTER KAG - KeyMod™
BCMGUNFIGHTER KAG - KeyMod™


 
Alternative Views:


List Price: $21.00
Our Price: $18.95

Stock Status:In Stock
Product Code: BCM-KAG-KM-BLK
Qty:

Description
 

BCMGUNFIGHTER™ KAG-KM

Kinesthetic Angled Grip - KeyMod Version

The KAG is the end result of collaboration between BCM® and Travis Haley, founder of Haley Strategic Partners and inventor of multiple weapons manipulation enhancements in the firearms industry.

Designed to complement modern shooting grips, the Kinesthetic Angled Grip (KAG) uses a biomechanically efficient forward rake to create an interface for positive retention and joint relief to the wrist, elbow, and shoulder, allowing for smooth weapon manipulation without substantial increase to the girth of the weapon system. Textured on both front and back, the profile of the KAG creates a channel for consistent and positive engagement which translates directly into improved efficiency in weapons manipulation and target to target transitions.


• Forward rake gives positive retention when using “C-clamp” (thumb over bore) method of handguard support

• Works as a rest for supported firing positions

• Slight angle without significant bulk adds just the right amount of relief to the wrist without substantially increasing the girth of the handguard

• Small profile is just enough to get repeatable hand position on weapon forend

• Innovative patent pending attachment method allows for robust clamping and alignment with minimal hardware and slender accessory size

• Textured in front and back for positive engagement

• Made in the U.S.A. from high quality, impact resistant polymers.


Installation Instructions - Tools needed: T15 Torx Driver (not supplied)


• Insert tool (T15 Torx™ driver) into the screw from under the BCM KeyMod™ KAG Handstop

• Push tool into screw to extend the KeyMod™ anchor, making it protrude from the top

• Align the anchors to the two selected large holes of the desired KeyMod™ slots

• After the anchor is inserted, slide the KAG Handstop forward until it travels no further

• Push the Handstop against rail, engaging the accessory’s recoil lug to the intersecting KeyMod™ opening

• With the Recoil Lug engaged, tighten screw to snug the anchor (approximately 40 inch-lbs. plus quarter turn*DO NOT OVERTIGHTEN*)

• Ensure there is no “play” or forward/backward movement once tightened.


*Blue thread locker may be used on threaded fasteners


Average Customer Review: Average Customer Review: 5 of 5 5 of 5 Total Reviews: 324 Write a review.

  0 of 0 people found the following review helpful:
 
5 of 5 Feels great! October 17, 2019
Reviewer: Mike K from Dallas, TX  
Easy to install. Tried it in a few different spots to see how it feels. Found the right spot and tightened it down. So intuitive! My hand goes to the same spot every time. Doesn't interfere with my off-hand grip. Well done!
The Torx T15 screw angered me when I first saw it. Then I realized I had the driver in my Fat Wrench torque driver set. Torx  is less likely to be stripped out compared to Allen screws. Good choice.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Feels natural October 17, 2019
Reviewer: Jeff Eggers from Redding, CA United States  
Funny how a simple mod , could make such a large Benefit to repeatable hand holds!

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Bcm kag keymod October 17, 2019
Reviewer: Jason Lindsey from Perryopolis, PA United States  
First time buying from bcm and product and shipping was perfect. Could not ask for a better experience.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Recce 16 precision rifle. October 17, 2019
Reviewer: HANS SCHMID from MIAMI, FL United States  
Great experience with the purchasing, will be returning in the near future.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Fantastic grip October 17, 2019
Reviewer: Jeremy Sommers from Brookshire, TX United States  
This grip coupled with a 1.5" diameter keymod rail make it very easy to hold a firm C-clamp grip on my AR. Highly recommend.

Was this review helpful to you?

View All Customer Reviews

Browse for more products in the same category as this item:

Stocks, Grips, and Handguards > Vertical Grips, Hand Stops
Stocks, Grips, and Handguards
Accessories > KeyMod™ Accessories
Accessories