Home > Stocks, Grips, and Handguards > Vertical Grips, Hand Stops >

BCMGUNFIGHTER KAG - KeyMod™ - Wolf Gray

BCMGUNFIGHTER KAG - KeyMod™
BCMGUNFIGHTER KAG - KeyMod™


 
Alternative Views:


List Price: $21.00
Our Price: $18.95

Stock Status:In Stock
Product Code: BCM-KAG-KM-WG
Qty:

Description
 

BCMGUNFIGHTER™ KAG-KM

Kinesthetic Angled Grip - KeyMod Version

The KAG is the end result of an ongoing collaboration between BCM® and Travis Haley, founder of Haley Strategic Partners and inventor of multiple weapons manipulation enhancements in the firearms industry.

Designed to complement modern shooting grips, the Kinesthetic Angled Grip (KAG) uses a biomechanically efficient forward rake to create an interface for positive retention and joint relief to the wrist, elbow, and shoulder, allowing for smooth weapon manipulation without substantial increase to the girth of the weapon system. Textured on both front and back, the profile of the KAG creates a channel for consistent and positive engagement which translates directly into improved efficiency in weapons manipulation and target to target transitions.


• Forward rake gives positive retention when using “C-clamp” (thumb over bore) method of handguard support

• Works as a rest for supported firing positions

• Slight angle without significant bulk adds just the right amount of relief to the wrist without substantially increasing the girth of the handguard

• Small profile is just enough to get repeatable hand position on weapon for-end

• Innovative patent pending attachment method allows for robust clamping and alignment with minimal hardware and slender accessory size

• Textured in front and back for positive engagement

• Made in the U.S.A. from high quality, impact resistant polymers.


Installation Instructions - Tools needed: T15 Torx Driver (not supplied)


• Insert tool (T15 Torx™ driver) into the screw from under the BCM KeyMod™ KAG Handstop

• Push tool into screw to extend the KeyMod™ anchor, making it protrude from the top

• Align the anchors to the two selected large holes of the desired KeyMod™ slots

• After the anchor is inserted, slide the KAG Handstop forward until it travels no further

• Push the Handstop against rail, engaging the accessory’s recoil lug to the intersecting KeyMod™ opening

• With the Recoil Lug engaged, tighten screw to snug the anchor (approximately 40 inch-lbs. plus quarter turn*DO NOT OVERTIGHTEN*)

• Ensure there is no “play” or forward/backward movement once tightened.


*Blue thread locker may be used on threaded fasteners


Average Customer Review: Average Customer Review: 5 of 5 5 of 5 Total Reviews: 31 Write a review.

  0 of 0 people found the following review helpful:
 
5 of 5 November 6, 2019
Reviewer: Brian from Holloman  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 November 2, 2019
Reviewer: Nick from Austin, TX  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
4 of 5 As expected October 17, 2019
Reviewer: Thomas Kuntz from Laurel, MD United States  
Fit and finish was good it's nice and light weight

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 June 4, 2019
Reviewer: Seth Holt from Urich, MO United States  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 June 4, 2019
Reviewer: Jordan Fall from Fleming Island, FL United States  


Was this review helpful to you?

View All Customer Reviews

Browse for more products in the same category as this item:

Stocks, Grips, and Handguards > Vertical Grips, Hand Stops
Stocks, Grips, and Handguards
Accessories > KeyMod™ Accessories
Accessories