BCM® 300 Blackout Barrels
Continuous taper designed for optimal weight, balance, and performance.
Fluted profile toward the rear near chamber area - Increases strength and heat dissipation.
Tapered profile out front, for easier maneuverability.
No sharp handguard cap shoulder for improved barrel harmonics and improved accuracy.
This barrel will need a pistol length gas tube and a .750 gas block.
Muzzle threaded in standard 30 cal (5/8x24)
BCM® has taken great care to ensure the best possible performance and interchangeability. However, due to the large operational range of 300 Blackout ammunition in the market place, BCM cannot guarantee function will all ammunition types in all conditions. These barrels were designed to run with a carbine buffer with subsonic ammo and a H3 buffer with high velocity ammo. Fine tuning may be required in limited instances based on ammo choices and buffer choices that works best for their application. BCM also recommends running the Crane O-ring (provided with all BCM Bolt Carrier Groups) over the extractor with 300 Blackout.
Continuous taper designed for optimal weight, balance, and performance.
Fluted profile toward the rear near chamber area - Increases strength and heat dissipation.
Tapered profile out front, for easier maneuverability.
No sharp handguard cap shoulder for improved barrel harmonics and improved accuracy.
This barrel will need a pistol length gas tube and a .750 gas block.
Muzzle threaded in standard 30 cal (5/8x24)
BCM® has taken great care to ensure the best possible performance and interchangeability. However, due to the large operational range of 300 Blackout ammunition in the market place, BCM cannot guarantee function will all ammunition types in all conditions. These barrels were designed to run with a carbine buffer with subsonic ammo and a H3 buffer with high velocity ammo. Fine tuning may be required in limited instances based on ammo choices and buffer choices that works best for their application. BCM also recommends running the Crane O-ring (provided with all BCM Bolt Carrier Groups) over the extractor with 300 Blackout.
- Caliber: 300 Blackout
- Length: 9"
- Weight: 15 oz
- Twist Rate: 1:7
- Steel: 11595E Certified
- Exterior Finish: Manganese Phosphate
- Bore Chamber Finish: Chrome Lined
- Bore Honed Prior To Rifling
- Gas System: Pistol
- Muzzle Threads: 5/8x24
- Diameter at Gas Block: .750"
PLEASE NOTE: These batches can sell out quickly.
If the Stock Status is Out of Stock and you would like to get notification when more product arrives, please click the "Email me when Back-In-Stock" link under the Add To Cart button. You will get immediate notification of all new arrivals of product.
If you get an email notification and you check back again with our website to see that the product has already again sold out, please click the link again and add your email to the notification list.
Please check back with our website often. Sorry but we cannot take pre-orders or backorders on these products.
Life Saving Tools
M4 Feed Ramp Barrel Extension
In developing the USGI M4 carbine as one of the primary weapons for todays infantry, some modifications were performed to the original M16 platform to enhance the reliability of the shorter barreled carbines. With the shorter carbine gas system and the increased gas port pressure, the carbine cycled faster, and at times the cycle rate could be faster than the magazine would feed ammunition. One of the modifications done to increase reliable feeding included enhancing the angle and the length of the feed ramps. This USGI modification was done to both the barrel extension and the upper receiver, creating a longer and steeper feed ramp. These Mil-Spec M4 feed ramps are part of the original CNC manufacturing process. As a result, the factory machined M4 feed ramps on the receiver are hard coat anodized which adds significant strength to the aluminum. This feature is offered on all BCM barrels.
Mil-Spec Barrel Steel (Mil-B-11595E)
BCM barrel steel is Mil-Spec per MIL-B-11595E. This grade (CMV) of steel is a Mil-Spec steel used in the USGI M16 family of rifles; it is stronger and will last longer than the typical barrels offered in the commercial market. The Mil-Spec grade steel gets its additional strength and rigidity from an increase in carbon and/or vanadium in the alloy. This will offer increased barrel life and performance through use in all types of extreme environments and temperatures.
Chrome Bore and Chamber
One of the first modifications that were made to the original M16 in the mid 1960s was the addition of the chrome lined bore and chamber. It is now a world wide standard in the industry for a battle rifle. The chrome bore and chamber is harder than the barrel steel and on the USGI M16/M4 rifles will aid in chambering, extraction, and reliability. It increases velocity, and also resist against fouling and corrosion from extended use in the field. This gives the end user a longer barrel life with less required time in maintenance and cleaning.
Manganese Phosphate Barrel Finish
Barrels are parkerized with the manganese phosphate finish (Mil-Spec A-A-59267). Military specifications also state that the entire barrel surface is phosphate finished to create a porous surface to absorb oil as to resist against corrosion from the elements. BCM barrels are phosphated before installation of front sights. This is a much more extensive assembly operation, but insures that the entire barrel is finished and protected.
Copyright 2015 Bravo Company MFG, Inc.
